The smallest size Gigabit Ethernet Test Set in the market, designed with powerful features and flexibility for your network trouble-shooting and verification needs within your budget.

• Intercept ARP Spoofing/Attack/Poison
• Intercept IP Conflict
• Incoming ARP Packet Analysis
• Protect ARP Cache
• Active Defence
• Trace Attacker

• Support PING function for connectivity detection to any remote device in the network.
• Support Fixed IP or DHCP mode for acquiring IP address.
• Able to monitor or force the link status for its duplex mode (full or half), link speed (10, 100, 1000 Mbps), TX/RX pair in the cable, link quality, flow control status & auto-negotiation capability.
• Able to shutdown the tester at user specified interval when not in operation.
• Able to FLASH remote port LED for port identification.
• Able to do ARP scan to search all the devices in the specified network for its MAC address, IP address and the associated host name.

• With two GiLaner connected to the network, the system can perform the upstream and downstream traffic flow simultaneously at various different rate.
• This is a great feature in XDSL/FTTx application for bi-directional bandwidth simulation and verification.

• The RFC2544 definition describes six standard tests that are used to measure and report the performance characteristics of network equipment. GiLaner can support the throughput, frame loss rate, back-to-back frames, and latency tests.

• Able to measure the UTP & STP cable length up to 150 meters long for OPEN/SHORT status. When SFP transceiver with Diagnostic Monitoring Interface is used, the tester can display the TX/RX power, temperature, Laser Bias Current, & voltage for quick diagnostic on the fiber link.

• Able to record up to 80 sets of report by entering test date, test person, filename, and test site.
• Each report can be exported to PC in ASCII text format at the touch of a button.

• Able to identify the port in the switch/router that is under test from the remote.

• Able to perform 10/100/1000 Mbps framed layer 1(packet with preamble followed by PRBS data), and framed layer 2 (packet in 802.3 format) test.
• PRBS data pattern supported are: 2⁷?, 2¹⁵?, 2²⁰?, 2²³?, 2³¹?

• These three models have 2 ports installed, use the versatile through-mode provided by the tester for advanced troubleshooting. This mode allows bandwidth usage to be analyzed with results and findings shown in the statistics view.

• Able to perform trace route test to identify all MAC and IP address as well as its associated hostname in the route to the remote node.

• Support single or multi streams (Up to 8 streams) can be individually configured with traffic generation setup.
• Able to configure FDX/HDX, preamble size, TX sequence tag, flow control and auto-negotiation.
• Able to generate packet with variable data length ranging from 46 ~ 9000 bytes at up to 100% wire speed rate.
• Generated packets can be varied with link speed( 10/100/1000 Mbps), duplex mode(full/half), TX packet number, or TX timer, or Non-Stop, packet length, data pattern, Source/ Destination MAC/IP address, VLAN ID and Priority, Double VLAN (QinQ), and TX utilization rate.
• Able to generate error frames such as: oversize, undersize, dribble, alignment and FCS errors.
• Able to do Constant / Burst transmission type.
• Able to perform RFC2544 performance analysis which includes throughput test, frame loss rate test, back-to-back test & latency test.
• Able to perform Internet work Throughput with two GiLaner (Up/Down stream test).
• IPV4 packet generation with checksum at wired speed. The IP header is programmable by the user.

• Various statistics counter of real time TX/RX PPS(Packets Per Second), TX/RX Utilization %, TX/RX Bandwidth, TX/RX Frames, VLAN, Pause Frame, Bit Error Count, Unicast, Multicast, Broadcast, Dribble, Alignment, Collision, Undersize, Oversize & FCS errors are all provided.

• Able to manually control for loop-back operation.
• ARP supported, MAC/IP source/destination address, port number swapped automatically.
• Able to loop-back all incoming traffic unchanged including invalid frames

• MAC/IP source and destination address
• ARP, Multicast or Broadcast
• TCP/UDP
• VLAN ID/Priority
• Data Pattern for MPLS Tag, IP TOS, Cisco DSCP

• Throughput
• Frame Loss
• Back-To-Back
• Latency

• Traffic Generation
• BER test
• Bidirectional upstream/downstream test
• Loopback mode

• PING remote host to check network connectivity
• Trace-route test to identify all the MAC/IP/Hostname in the route to the remote host.
• Flash port to identify the remote port in the switch/router as a means to find out which port the cable is connected to from the remote.

• Link: Up or Down
• Duplex: Full or Half Duplex
• Speed: Current Link mode (10 /100/1000 Mbps)
• Quality: The signal strength for copper link (Good, Poor or Marginal)
• Flow control: to see the flow control capability of current link
• Auto-negotiation: to see the auto-negotiation capability of current link